View source for Short circuit

{{otheruses}}
[[Image:Crossed wires.JPG|thumb|Tree limbs cause a short circuit during a storm]]

A '''short circuit''' (sometimes abbreviated to '''short''' or '''s/c''') in an [[electrical circuit]] allows a [[Electric current|current]] along a different path from the one intended.  
The electrical opposite of a short circuit is an "[[open circuit]]", which is an infinite resistance between two nodes. It is common to misuse "short circuit" to describe any electrical malfunction, regardless of the actual problem.

==Definition==
A short circuit is an abnormal low-[[Electrical resistance|resistance]] connection between two nodes of an [[electrical circuit]] that are meant to be at different voltages.  This results in an excessive [[electric current]] ([[overcurrent]]) limited only by the [[Thévenin's theorem|Thevenin equivalent resistance]] of the rest of the network and potentially causes circuit damage, overheating, [[fire]] or [[explosion]]. Although usually the result of a fault, there are cases where short circuits are caused intentionally, for example, for the purpose of voltage-sensing [[Crowbar (circuit)|crowbar circuit protectors]].
<br><br>
In [[circuit analysis]], the term short circuit is used by analogy to designate a zero-impedance connection between two nodes. This forces the two nodes to be at the same voltage. In an ideal short circuit, this means there is no resistance and no voltage drop across the short. In simple circuit analysis, wires are considered to be shorts. In real circuits, the result is a connection of nearly zero [[Electrical impedance|impedance]], and almost no resistance. In such a case, the current drawn is limited by the rest of the circuit.

== Examples ==

A short circuit is to connect the positive and negative terminals of a [[Battery (electricity)|battery]] together with a low-[[electrical resistance|resistance]] [[Electrical conductor|conductor]], like a [[wire]].  With low resistance in the connection, a high [[Current (electricity)|current]] exists, causing the cell to deliver a large amount of [[energy]] in a short time.

In electrical devices, unintentional short circuits are usually caused when a wire's [[Electrical insulation|insulation]] breaks down, or when another conducting material is introduced, allowing charge to flow along a different path than the one intended.

A large current through a battery (also called a [[Electrochemical cell|cell]]) can cause the rapid buildup of heat, potentially resulting in an explosion or the release of [[hydrogen]] gas and [[electrolyte]], which can burn tissue and may be either an [[acid]] or a [[base (chemistry)|base]]. Overloaded wires can also overheat, sometimes causing damage to the wire's insulation, or a fire.  High current conditions may also occur with [[electric motor]] loads under stalled conditions, such as when the impeller of an electrically driven [[pump]] is jammed by debris; this is not a short, though it may have some similar effects.

In [[mains]] circuits, short circuits are most likely to occur between two [[Polyphase system|phases]], between a phase and [[Ground and neutral|neutral]] or between a phase and [[Ground and neutral|earth]] (ground).  Such short circuits are likely to result in a very high current and therefore quickly trigger an overcurrent protection device. However, it is possible for short circuits to arise between neutral and earth conductors, and between two conductors of the same phase. Such short circuits can be dangerous, particularly as they may not immediately result in a large current and are therefore less likely to be detected. Possible effects include unexpected energisation of a circuit presumed to be isolated. To help reduce the negative effects of short circuits, power distribution transformers are deliberately designed to have a certain amount of [[Leakage inductance|leakage reactance]]. The leakage reactance (usually about 5 to 10% of the full load impedance) helps limit both the magnitude and rate of rise of the fault current.

== Damage ==

Damage from short circuits can be reduced or prevented by employing [[Fuse (electrical)|fuses]], [[circuit breaker]]s, or other overload protection, which disconnect the power in reaction to excessive current.  Overload protection must be chosen according to the [[maximum prospective short circuit current]] in a circuit. For example, large home appliances (such as clothes dryers) typically draw 10 to 20 amperes, so it is common for them to be protected by 20&ndash;30 ampere circuit breakers, whereas lighting circuits typically draw less than 10 amperes and are protected by 15&ndash;20 ampere breakers. [[Wire gauge]]s are specified in building and electrical [[building code|codes]], and must be carefully chosen for their specific application to ensure safe operation in conjunction with the overload protection.

== See also ==
{{portalpar|Electronics|Nuvola_apps_ksim.png}}

* [[Ohm's law]]
* [[Power (physics)]]

==External links==
{{Wiktionary|short circuit}}

* [http://www.thecircuitdetective.com/tsing.htm#short Troubleshooting Strategy for US/Canadian Homes] The Circuit Detective


[[Category:Electronics terms]]
[[Category:Electrical engineering]]

[[ar:دائرة قصر]]
[[ca:Curtcircuit]]
[[cs:Zkrat]]
[[de:Elektrischer Kurzschluss]]
[[et:Lühis]]
[[es:Cortocircuito]]
[[eo:Kurta cirkvito]]
[[fr:Court-circuit]]
[[id:Hubungan pendek]]
[[is:Skammhlaup]]
[[it:Cortocircuito]]
[[he:קצר חשמלי]]
[[lt:Trumpasis jungimas]]
[[hu:Rövidzárlat]]
[[ms:Litar pintas]]
[[nl:Kortsluiting]]
[[ja:短絡]]
[[no:Kortslutning]]
[[pl:Zwarcie (elektrotechnika)]]
[[pt:Curto-circuito]]
[[ru:Короткое замыкание]]
[[sk:Skrat]]
[[fi:Oikosulku]]
[[sv:Kortslutning]]
[[uk:Коротке замикання]]
[[zh:短路]]